saw bandpass filter act part no.: act f 9357 _2140mhz_dcc6c_v1.0 product type : customer: saw filter part n o . : customer part n o . : act f 9357 _2140mhz_dcc6c_v1.0 issued date : prepared by checked by approved by
features ? low - loss rf filter ? high rejection ? single en ded operation at 50 without matching ? ceramic package for s urface m ounted t echnology ( smt ) ? lead- free production and rohs compliance package dimension s ceramic package: dcc6c pin configuration 2 input 5 output 1, 3, 4, 6 case ground 1, 3, 4, 6 to be grounded mar king act f 9357 top view, laser marking " act ?: manufacturer?s mark ? f ?: saw filter ? 9357 ?: part number ? ?: terminal 1 ??: lot number (the code shown below varies in a 4 - year cycle) code 1 2 3 4 5 6 7 8 9 10 11 12 2011 a b c d e f g h i j k m 201 2 n p q r s t u v w x y z 2013 a b c d e f g h j k l m 2014 n p q r s t u v w x y z - 2 -
maximum ratings rating value unit input power level p 24.5 dbm cw ta=85 c life time> 2 hurs 2 4 dbm cw ta=95 c life time> 2 hurs 18 dbm cw ta=85 c life time>1000 hurs 17 dbm cw ta=95 c life time>1000 hurs 13 dbm cw ta=85 c life time>100 , 0 00 hurs 12 dbm cw ta=95 c life time>100 , 0 00 hurs dc v oltage v dc 0 v esd voltage (hb) v esd 150 v operating t emperature r ange t a -40 ~ + 95 c storage t emperatur e r ange t stg - 40 ~ + 9 5 c electrical characteristics item minimum typical maximum unit center frequency f c - 2140 - mhz maximum insertion loss in 2110 mhz ? 2170 mhz il - 3.0 3 .5 db amplitude variation in 2110 mhz ? 2170 mhz 1.0 1. 5 db absolute atte nuation 5 0. 0 ? 1400. 0 mhz 2 2 2 7 - db 1400. 0 ? 1910.0 mhz 2 5 2 8 - db 1910. 0 ? 1980.0 mhz 30 3 8 - db 2300 .0 ? 3700 .0 mhz 25 3 0 -- db 37 00 .0 ? 53 00 .0 mhz 2 0 25 -- db 5300 .0 ? 5700 .0 mhz 15 18 -- db input vswr in 2110 mhz ? 2170 mhz - 1. 5:1 2.0:1 o utput vswr in 2110 mhz ? 2170 mhz - 1. 5:1 2.0:1 group delay ripple 2110 mhz ? 2170 mhz 10 30 ns source / load impedance (single ended) 50 rohs c ompli ant electrostatic sensitive device - 3 -
typical frequency response s11 s22 - 4 -
s21 stability c haracteristics test item condition of test 1 mechanical shock (a) drops: 3 times on concrete floor (b) height: 1.0 m 2 vibration resistance (a) frequency of vibration: 10 ~ 55hz (b) amplitude: 1.5 mm (c) directions: x,y and z (d) duration: 2 hours 3 moisture resistance (a) condition: 40c, 90~95% r.h. (b) duration: 96 hours (c) wait 4 hours before measurement 4 climatic sequence (a) + 70c for 16 hours (b) +55 c for 24 hours, 90~95% r.h. (c) -25c for 2 hours (d) +40 c for 24 hours, 90~95% r.h. (e) wait 4 hours before measurement 5 high t emperature e xposure (a) temperature: 70c (b) duration: 250 hours (c) wait 4 hours before measurement 6 thermal impact (a) +70c fo r 30 minutes ? - 25c for 30 minutes repeated 3 times (b) wait 4 hours before measurement requirements : the saw filer shall remain w ithin the electrical specifications after tests. - 5 -
remarks ? saw devices should not be used in a ny type of fluid such as water, oil, organic solvent, etc. ? be certain not to apply voltage exceeding the rated voltage of components. ? do not operate outside the recommended operating temperature range of components. ? sudden change of temperature shall be av oided, deterioration of the characteristics can occur. ? be careful of soldering temperature and duration of components when soldering. ? do not place soldering iron on the body of components. ? be careful not to subject the terminals or leads of components to e xcessive force. ? saw devices are electrostatic sensitive . p lease avoid static voltage during operation and storage. ? u ltrasonic cleaning shall be avoided . ultrasonic vibration may cause destruction of components. test circuit recommended land pat tern 50 / 50 configuration packing information carrier tape - 6 -
reel dimensions outer packing type quantity dimension description weight carton box 0.85 carton box 2 0000 190190190 1. 7 0 unit: mm unit: kg recommended soldering profile c e a act 201 3 all rights reserved. 1. the specifications of this device are subject to change or obsole scence without notice. 2. typically, equipment utilizing this device requires emissions testing and government approval, which is the responsibility of the equipment manufacturer. 3. our liability is only assumed for the surface acoustic wave (saw) component(s) per se, not for applications, processes and circuits implemented within components or assemblies. - 7 -
|
